[[PageOutline(1-3,"Table of Content")]] This guide will tell you how-to put FreeBSD 9.x on an (ALIX) embedded device. For FreeBSD 8.x see the archived guide for hints [[wiki:Archive/FreeBSDOnEmbeddedDevice]] TODO: This is NOT complete yet. Tip: I set the prompt on various location such that the output reflects the terminal output. build# set prompt = "build# " = Initial disk configuration = Please do mind I create a 6G image to be used at a 8G CF disk as making it exactly fit, causes issues if sectors are wearing out. I create 2 x 2G partitions for the OS (and backup OS) and 1 x 1G partition for various configuration files and other shared stuff. build# truncate -s 6GB embedded.img build# MD=`mdconfig embedded.img` build# gpart create -s MBR md0 build# gpart add -t freebsd -s 2G build# gpart add -t freebsd -s 2G build# gpart add -t freebsd -s 1G build# newfs md0s1 md0s2 md0s3 = Disk population = build# setenv RELEASE 9.0-RELEASE build# mkdir -p /usr/data/$RELEASE build# cd /usr/data/$RELEASE build# fetch ftp://ftp.nl.freebsd.org/pub/FreeBSD/releases/i386/$RELEASE/base.txz build# fetch ftp://ftp.nl.freebsd.org/pub/FreeBSD/releases/i386/$RELEASE/kernel.txz build# fetch ftp://ftp.nl.freebsd.org/pub/FreeBSD/releases/i386/$RELEASE/docs.txz More sophisticated approach (rsync not in base): build# rsync -vaz ftp.nl.freebsd.org::FreeBSD/releases/i386/$RELEASE/ . build# setenv DESTDIR /mnt build# xzcat base.txz | tar --unlink -xpzf - -C $DESTDIR build# xzcat kernel.txz | tar --unlink -xpzf - -C $DESTDIR build# xzcat docs.txz | tar --unlink -xpzf - -C $DESTDIR Tip: Soekris 2521 requires CPU_ELAN which is not included into the kernel by default. For optimal performance compile the kernel yourself = Image configuration Chroot = Need resolving power at later stage inside chroot: build# cp /etc/resolv.conf /mnt/etc/ Need ssh-keygen to work, so need access to /dev/urandom build# mount -t devfs devfs /mnt/dev build# chroot /mnt build# set prompt = "chroot# " = Image configuration = Important: if you FAIL to chroot and continue you will now start destroying your build system Tip: Having your flash living in read-only gives you added security and increases the live-time of your (older) Flash cards. read-write is more convenient But you will need to do some tricks as some programs need rw on first boot for ssh keys and such. chroot# echo "/dev/ada0s1 / ufs rw,noatime 0 1" > /etc/fstab Make sure to continue to check the disks on reboot, instead of waiting for user input: chroot# echo "fsck_y_enable=YES" >> /etc/rc.conf {{{ #!sh chroot# cat < /boot/loader.conf console=comconsole autoboot_delay=3 hw.ata.ata_dma=0 # Soekris boot failure EOF }}} Serial console boot only: chroot# echo "-h" > /boot.config Enable serial console: chroot# sed -I '' '/ttyu0/ s/off/on /' /etc/ttys Cosmetic: disable all vidconsoles as a soekris embedded device does not have any: chroot# sed -I '' '/ttyv[0-7]/ s/on /off/g' /etc/ttys == Accounting & access control == chroot# echo "sshd_enable=YES" >> /etc/rc.conf chroot# service sshd keygen chroot# pw usermod root -w random Administive user (admin for example): chroot# pkg_add -r sudo chroot# pw useradd admin -G wheel -c 'Admin User' -s /bin/csh -m -w random chroot# echo '%wheel ALL=(ALL) ALL' >> /usr/local/etc/sudoers == Networking == chroot# hostname riff.vanderzwet.net chroot# echo hostname=`hostname` >> /etc/rc.conf Warning: IPv4 and IPv6 is provided example only, provide your own local IP configuration {{{ #!sh # chroot# cat <<'EOF' > /etc/rtadvd.conf bridge0:\ :addrs#1:addr="2001:1af8:febe::":prefixlen#64:tc=ether: EOF }}} {{{ #!sh # chroot# <<'EOF' >> /etc/rc.conf cloned_interfaces="bridge0" wlans_ath0="wlan0" # Internal wired and wireless ifconfig_vr0="up" create_args_wlan0="wlanmode hostap country NL mode 11g ssid home.vanderzwet.net up" ifconfig_bridge0="addm wlan0 addm vr0 up" ipv4_addrs_bridge0="192.168.42.1/24 192.168.1.2/24" ipv6_ifconfig_bridge0="fe80::2 prefixlen 64" ipv6_ifconfig_bridge0_alias0="2001:1af8:febe::1 prefixlen 64" # Wireless Leiden Connections ifconfig_vr2="up" ipv4_addrs_vr2="172.20.145.130/26" # Internet ifconfig_vr1="DHCP" static_routes="wleiden" route_wleiden="-net 172.16.0.0/12 172.20.145.129" ipv6_defaultrouter="2001:1af8:fe00:28e::1" ipv6_network_interfaces="auto" rtadvd_interfaces="bridge0" rtadvd_enable="YES" EOF }}} {{{ #!sh # chroot# cat <<'EOF' > /etc/hostapd.conf interface=wlan0 driver=bsd logger_syslog=-1 logger_syslog_level=0 logger_stdout=-1 logger_stdout_level=2 dump_file=/tmp/hostapd.dump ctrl_interface=/var/run/hostapd ctrl_interface_group=0 macaddr_acl=0 auth_algs=1 wpa=1 wpa_passphrase=ThisPasswordIsPublic! wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP TKIP EOF }}} {{{ #!sh # chroot# <<'EOF' > /etc/pf.conf inet_if="vr1" wleiden_if="vr2" int_if="bridge0" int_network="192.168.42.0/24" # Do not do anything @ localhost set skip on lo0 ### all incoming traffic on external interface is normalized and fragmented ### packets are reassembled. scrub in all fragment reassemble nat on $inet_if from $int_network -> ($inet_if:0) nat on $wleiden_if from $int_network -> ($wleiden_if:0) # SSH Access for proxy13 rdr pass on $inet_if proto tcp from any to any port 2022 \ -> 192.168.42.146 port ssh # SSH Access for CNodeRick nat on $wleiden_if from any to 172.20.145.129 port ssh -> ($wleiden_if:0) rdr pass on $inet_if proto tcp from any to any port 1022 \ -> 172.20.145.129 port ssh # No firewall configured pass quick on $int_if no state pass out on $inet_if keep state pass out on $wleiden_if keep state pass in on $inet_if keep state pass in on $wleiden_if keep state EOF }}} == Package install == Get your packages locally if possible: {{{ chroot# cat <> /etc/csh.cshrc setenv FTP_PASSIVE_MODE yes setenv PACKAGEROOT ftp://ftp.nl.FreeBSD.org EOF }}} chroot# source /etc/csh.cshrc === dnsmasq === dnsmasq used for local network dns and dhcp: chroot# pkg_add -r dnsmasq chroot# echo "dnsmasq_enable=YES" >> /etc/rc.conf chroot# setenv DOMAIN `hostname | sed 's/^[^.]*.//'` {{{ #!sh node# cat < /usr/local/etc/dnsmasq.conf interface=bridge0 no-dhcp-interface=vr1 cache-size=10000 localise-queries domain=${DOMAIN}. dhcp-range=bridge0,192.168.42.100,192.168.42.200 dhcp-host=00:00:24:c1:1d:d0,192.168.42.130 dhcp-host=00:13:d3:a7:24:51,192.168.42.165 dhcp-option=option:router,192.168.42.1 server=/wleiden.net/172.20.145.129 `jot 16 16 | xargs -n 1 -I % echo server=/%.172.in-addr.arpa/172.20.145.129` EOF }}} === ntp === node# echo "ntpd_enable=YES" >> /etc/rc.conf {{{ node# cat < /etc/ntp.conf server 0.nl.pool.ntp.org server 1.nl.pool.ntp.org server 2.nl.pool.ntp.org driftfile /var/db/ntp.drift EOF }}} === motd === node# (sed '3,$ d' /etc/motd; echo "WWW: riff.vanderzwet.net - http://rickvanderzwet.nl" ) > /etc/motd.new; mv /etc/motd.new /etc/motd === Flash disk protection === chroot# echo "update_motd=NO" >> /etc/rc.conf chroot# echo "tmpmfs=YES" >> /etc/rc.conf chroot# echo "varmfs=YES" >> /etc/rc.conf Tip: I hate the details like package management details getting lost. Flash cards these days are cheap anyways, mine lived for 1 year after extensive use. Of course with read-only this will be _much_ longer. chroot# sed '/1a/ s/rw/ro/' /etc/fstab > /etc/fstab.new; mv /etc/fstab.new /etc/fstab === various === Tip: Use your favourite package list over here chroot# pkg_add -r tinyproxy sudo vim-lite subversion sixxs-aiccu apache22 transmission-daemon == Last Minute Changes == Make any other optional changes before first boot inside chroot(8): chroot# vi /etc/rc.conf = Put into production = First make sure to exit your chroot: chroot# exit Umount the active mountpounts: build# umount /mnt/dev /mnt Stop your memory disk: build# mdconfig -u $MD Hack to reload the usb card reader to reread partition tables: build# usbconfig -d `usbconfig | awk -F : '/Mass/ {print $1}'` reset Have a look to which card (da1 in mine case) you like to install it: build# grep sectors /var/log/messages > Feb 2 12:55:12 brahm kernel: da1: 7629MB (15625216 512 byte sectors: 255H 63S/T 972C) Tip: During this process you can press CTRL+T to send SIGINFO, this will tell you the current state of the code. Important: The following action will DESTROY all the existing content on the configured device. USE AT OWN RISK. Now clone your image onto your flashcard: build# dd if=embedded.img of=/dev/da1 bs=64k Note: NOT READY YET: Insert card into your embedded device and get yourself a prompt, using serial of ssh login. = Production Maintenance = == Adding packages == Tip: As space is limited unpacking packages can result in I/O errors due to (memory) disks which run out of space. Installing for example the package apache22 goes as follows: node# mkdir /usr/local/tmp node# setenv PKG_TMPDIR /usr/local/tmp node# pkg_add -r -t /usr/local/tmp/instmp.XXXXXX apache22