|Version 17 (modified by 5 years ago) ( diff ),|
- Pre-printed parts by Mendel Parts (Mendel v2): http://reprap.org/wiki/Prusa_Mendel_(iteration_2)
- Elektronic board: http://reprap.org/wiki/Megatronics_2.0
- Running Marlin firmware: https://github.com/rickvanderzwet/Marlin/
Some handy pages to get started:
March 9, 2018
[rick@rvdzwet-wasus Marlin]$ lsb_release -a LSB Version: :core-4.1-amd64:core-4.1-noarch:cxx-4.1-amd64:cxx-4.1-noarch:desktop-4.1-amd64:desktop-4.1-noarch:... Distributor ID: Fedora Description: Fedora release 27 (Twenty Seven) Release: 27 Codename: TwentySeven [rick@rvdzwet-wasus ~]$ arduino java.awt.HeadlessException at java.awt.SplashScreen.getSplashScreen(SplashScreen.java:117) at processing.app.Base.<init>(Base.java:206) at processing.app.Base.main(Base.java:135) [rick@rvdzwet-wasus ~]$ rpm -qa | grep openjdk java-1.8.0-openjdk-headless-22.214.171.124-5.b14.fc27.x86_64 [rick@rvdzwet-wasus ~]$ sudo dnf install java-1.8.0-openjdk [rick@rvdzwet-wasus ~]$ arduino java.awt.HeadlessException: No X11 DISPLAY variable was set, but this program performed an operation which requires it. at java.awt.SplashScreen.getSplashScreen(SplashScreen.java:117) at processing.app.Base.<init>(Base.java:206) at processing.app.Base.main(Base.java:135) /usr/share/arduino/hardware/arduino/avr/boards.txt ############################################################## megatronics.name=Megatronics megatronics.upload.tool=avrdude megatronics.upload.protocol=wiring megatronics.upload.maximum_size=258048 megatronics.upload.speed=115200 megatronics.bootloader.low_fuses=0xFF megatronics.bootloader.high_fuses=0xDA megatronics.bootloader.extended_fuses=0xF5 megatronics.bootloader.file=stk500v2/stk500boot_v2_mega2560.hex megatronics.bootloader.unlock_bits=0x3F megatronics.bootloader.lock_bits=0x0F megatronics.build.mcu=atmega2560 megatronics.build.board=AVR_MEGATRONICS megatronics.build.f_cpu=16000000L megatronics.build.core=arduino megatronics.build.variant=mega
Difference between thermistor and thermocouple: https://electronics.stackexchange.com/questions/24975/differences-between-thermistors-and-thermocouples
March 10, 2018
Dead PSU Controller
start echo: External Reset Marlin 1.1.8 echo: Last Updated: 2017-12-25 12:00 | Author: (none, default config) echo:Compiled: Mar 10 2018 echo: Free Memory: 5418 PlannerBufferBytes: 1264 echo:Hardcoded Default Settings Loaded echo: G21 ; Units in mm echo:Filament settings: Disabled echo: M200 D3.00 echo: M200 D0 echo:Steps per unit: echo: M92 X80.00 Y80.00 Z4000.00 E500.00 echo:Maximum feedrates (units/s): echo: M203 X300.00 Y300.00 Z5.00 E25.00 echo:Maximum Acceleration (units/s2): echo: M201 X3000 Y3000 Z100 E10000 echo:Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel> echo: M204 P3000.00 R3000.00 T3000.00 echo:Advanced: S<min_feedrate> T<min_travel_feedrate> B<min_segment_time_us> X<max_xy_jerk> Z<max_z_jerk> E<max_e_jerk> echo: M205 S0.00 T0.00 B20000 X10.00 Y10.00 Z0.30 E5.00 echo:Home offset: echo: M206 X0.00 Y0.00 Z0.00 echo:PID settings: echo: M301 P22.20 I1.08 D114.00 ok T:18.87 /0.00 B:23.38 /0.00 @:0 B@:0
Listing of g-code (Gcode) found at: http://marlinfw.org/meta/gcode/
Bed temperature reported using M105 was incorrect since power supply was faulty causing interference on the IC measuring the temperature. Replaced power supply, all happy again.
Dead PSU heatbed
My resistor bed consist of of 4 x 2R2 (WH10) in series resulting in 9 Ohm, PSU does not like this low load conditions or is simply broken which would make my 2nd dead power supply. The new PSU is only 12V which is not heating up properly. According to Ohm's law (I = V/R or R = V/I or V = IR) and my resistor rating i get 1.3A, which in result would yield only (W = VI) 15.6W heating power, not sufficient since my total resistor capacity is 40W. Which would give me W = VI combined with V = IR becomes W = IRI. W=40, R=9, makes I = 2A. Which in result would require V to be 40W / 2A = 20V. To fix this I will need to change the resistor bed layout. Instead of 4 in series. Put two in parralel and next two pairs in serie.
Stepper motors turns the wrong way
The orientation of the stepper motors does not match the standard one in the Marlin firmware. Since I rather keep the firmware configuration as vanilla as possible reversing the connectors on the board is the easiest way to make it all compatible again.
In order to print a working nozzle is required, with proper temperature settings for this nozzle (185C) and feed rates (500). One way is to use manual codes to allow debugging. First set the temperature of the nozzle M104 S185 next ensure the extruder coordinates are relative avoiding math additions of feeding new PLA. Issue M83. Next wait till the temperature is right, by checking it manually M105 a few times. Set the extruder head to a free location (G0 X0 Y0 Z150) Feeding goes by G0 F500 E100. Check for clean flow, in this case it should not stick to the nozzle and look clean and smooth. Smoke is bad, because it means the PLA is boiling inside. Too cold will cause the PLA too stall while feeding. Feedrate (F factor) will determine overall printing speed of the printer, sometimes setting the temperature a bit higher could potentially make a faster feedrate, yet this really depends on the nozzle construction.